Your shopping cart is empty!
Solid Fuel Burner Tray X141.
Fits Mamod Te1a, SR1a, SP2, SW1 and many others.
Includes plastic handle
0 reviews / Write a review
Standard Long Safety Valve X005 Standard Safety valve for most Modern Mamod Steam Engines. ..
Brass Chimney CowlDimensions: 15 × 31 dia mmWeight 32gms..
Mamod Black Funnel.Small end that fits in to boiler.As shipped with all new Mamod Steam Engines.
Bulb for the MES Bulb Holder.For use with the dynamo..2.5v 0.75w.
MES Bulb Holder.Bakelite Base.With Screw Terminals.
Solid Fuel Burner Tray X141S.Fits Mamod SP2, SP4 Steam EnginesIncludes plastic handle and shield.
Crankshaft to fit the Mamod Traction Engine or Steam Roller TE1a or SR1a. 82mm long (excluding ..
Driving Bands for SA1 Roadster, Fire Engine & Limo.There are two bands in this pack.This is for ..
Driving bands for the Mamod Traction Engine TE1a and Steam Roller SR1a (Also TE1 and SR1) .There are..
Driving bands for the Mamod SW1 Steam Wagon.There are two bands in this pack.Consists of one large b..
Mamod's unjoined driving bands for general use .There are two bands in this pack.Can be use to link ..
Driving Bands for WS1 Workshop (4).There are four bands in this pack.Set of 4 drive bands to fit the..
Dynamo 1v to 4v Output.Supplied with plastic pulley. Wires soldered on ready to use. ..
Lubrication Oil 30ml.Essential for the smooth running of the steam engines.Recommended for the pisto..
Mamod Large Hub Caps.This pack contains 2 genuine Mamod large hub capsFits the rear wheels of the TE..
Mamod Reverse Lever TE1A SR1A.Fits the Traction Engine, Steam Roller, Steam wagon.
Mamod Small Hub Caps.This pack contains 2 genuine Mamod small hub capsFits the front wheels of the T..
Front fork assembly for the Mamod Steam Roller SR1.Includes the washer, nut and spring.
Mamod Steam Roller Front Rollers SR1Pack contain 2 rollers.Small Hub Caps are required to secure the..
Mamod Steam Roller Rear Wheels SR1aPack contains 2 wheels.Large Hub Caps are required to secure the ..
Canopy for the Mamod TE1a traction engineRed banner on side saying Mamod Steam Tractor.Knurled nut a..
Mamod TE1a Front Leaf Spring.Leaf spring to fit on the front axle of the Mamod TE1/TE1a Traction Eng..
Rear Wheels for the TE1a Traction Engine With TyresThis pack contains 2 wheel.Large hub caps are req..
Mamod Traction Engine Front Wheels Front Wheels for the TE1a Traction Engine, Showmans Engine a..
Mamod supplied bag of washers pack.Spring, trunnion bolt and small metal washer for the cylinder ass..
Pulley to fit the Mamod dynamo.2mm Shaft, Outer Dimensions will vary.
Scuttle that fits the Traction Engine, Steam Roller or Steam Wagon SW1Holds the burner tray in place..
Standard Sight Glass Assembly.To fit the larger style boilers.This style has the screw fitting and t..
SP4 / SP5 Piston Cylinder Assembly.Piston and Cylinder Assembly for the SP4 and SP5 static steam eng..
Standard Flywheel for the TE1a, SR1.Fits many models in the Mamod range including SR1a TE1a, SW1, MM..
Standard Piston Cylinder Assembly X301/X401.Includes washer, spring and bolt.Fits TE1a, SR1a, SW1, C..
Standard Whistle Assembly X034.Fits most Mamod Steam Engines.Uses the 1/4" BSF Thread.
Steering Rod TE1a, SW1, SW1a, SR1a for all older models prior to middle 2019 - 2BA Steering AdapterS..
Solid Fuel Burner Tray X141SP5.Fits Mamod SP5 Steam EnginesIncludes plastic handle and shield.
Standard Sight Glass.To fit the larger style boilers.
Mamod Tyres - Set of Four for the Mamod Steam Engine TE1aIncludes 2 Rear Tyres with Tread (One with ..
Standard Sight Glass and Seal.To fit the larger style boilers.
Essential Washers1 x Fibre Washer for the Water Level Plug (3/16" Internal Dia)1 x Fibre Washer for ..
Mamod short safety valve (1/4 inch BSF) Short (approximately 1") ¼" BSF Safety Valve for early..
Mamod water level plug. Used on many older models including the Tractor Engine, Steam Rollers a..
SP4 Flywheel, 2.5" Diameter Screws on to crankshaft.
SA1 Wheel for Roadster Complete with tyre There is no fixing screw of this wheel ONE ..
Dynamo 1v to 4v Output.Supplied with brass pulley. Wires soldered on ready to use. (A..
Brass Ferrule and Nut for Bottom of the older (prior to 2019) Mamod Steering Rod.Fits the older mode..
Large diameter safety valve to fit Mamod SE1, SE2 & SE3 3/8 inch thread. Releasing pressure..
Standard Mamod 1/4 Inch BSF Boiler Inserts Solder the insert in to the boiler.Suitable for the ..
Standard Mamod 3/16 Inch BSF Boiler Inserts Solder the insert in to the boiler.Suitable for the..
Standard Mamod 1/4 Inch BSF Boiler Blanks This can be used to blank off a spare boiler thread o..
Threaded boiler insert for the 3/8inch safety valve Used on Mamod SE2, SE3 and SE1 static engin..
Wick for Mamod type Meth BurnersAbout 300mm long
Steering Rod TE1a, SW1, SW1a, SR1a for all models made from the middle 2019 onwards - 4mm Steering A..
Copper pipe set for Te1a, SR1a and SW1 3 pipes in total, cut and shaped to the correct length.&..
Trunnion Spring and Washer for all types of Mamod oscillating piston cylinders engines. Include..
12mm Plastic Model Pulley to fit the Mamod dynamo. 2mm Shaft
Essential Washers 1 x Driving Band for SR1a and TE1a 1 x Fibre Washer for the Water Level ..
Essential Washers 1 x Bottle of Oil 1 x Driving Band for SR1a and TE1a 1 x Fibre Wash..